Outlaw Audio Firmware Update for Model 1070 Receiver
Installation Instructions
Before downloading the file that contains the Model 1070 software update
and the “loader" program needed to install it, we strongly recommend
that you read these instructions and then print a copy of them. This will help
you to make the upgrade process quick and easy.
System Requirements:
The following hardware and software is required to install the upgrade.
If your system does not meet these requirements, and you are unable to access
a computer that does meet these requirements, please contact Outlaw Audio
Customer Service.
- IMPORTANT NOTE: The RS-232 port must be a physical port on your
computer. USB-to-serial adaptors are not reliable and we do not recommend
their use as the upgrade may fail.
Here's a lnk to a "straight through" cable from CompUSA
- IMPORTANT NOTE: Do not use "null modem" cables, as they
will not create the signal path required for this upgrade.
Download Instructions:
- Before starting the download process, we recommend that you create a new
folder in your computer's directory named "Model 1070 Upgrade".
This will keep the files needed for the upgrade in one folder and separate
them from other programs and data.
- Once the new folder is created, click on the "Download Now" link at the
bottom of this page.
- After a few seconds your computer will prompt you to "Run"
or “Save" the file. Click "SAVE" and select the folder
you have just created as the target download file location.
- When the download is complete, close dialog boxes and exit your Internet browser.
- IMPORTANT NOTE: The upgrade process erases all user
settings that have been stored in your Model 1070. If you have done a preliminary
setup before performing the upgrade you are advised to record settings for input
configuration, speakers and crossovers, delays, tuner presets, and any other configuration
data on the worksheet in your Owner’s Manual. You will need to re-enter these
settings once the upgrade is complete.
Installation Instructions:
Once the needed files have been downloaded follow these instructions to perform the upgrade:
- Connect your Model 1070 to an AC power source.
- Turn on the Master Power switch on the rear panel by pressing it in until it latches.
Note that the front panel power indicator will turn amber. DO NOT use the front panel
Standby button to fully turn the unit on at this time.
- Connect the RS-232 serial cable to both your computer and the Model 1070.
- Locate the access hole for the RESET switch that is located in the center of the rear
panel, just to the right of the RS-232 connector. Using an unbent paper clip reset the unit
by carefully slipping the end of the wire directly straight into the access hole until you
hear and feel the reset switch click. Remove the paper clip from the hole.
- Use the Windows Explorer program to locate the file folder that contains OUTLAW.EXE file
downloaded from the Outlaw web site and click on the file to open it.
- The Outlaw Loader window will open. Follow the instructions shown on each page of the Loader,
including some of the instructions shown above, clicking on the NEXT button when each step is
completed.
- When you reach the page of the Loader titled "LOADER SETTINGS" enter the two
following settings:
- In most cases the default setting of COM 1 is correct. If not, select the appropriate
COM Port.
- Press the BROWSE button and locate the ot10700608.hex file in the "Model 1070
Upgrade" folder that you created at the beginning of this process. Click on the file name
and you will be returned to the Loader program.
- Click on the NEXT Button to begin the upgrade process.
- IMPORTANT NOTE: Once the upgrade begins it is very important that you do not disconnect the serial cable
from your computer to the Model 1070 or turn off either your computer or the Model 1070. Interrupting
the upgrade process will cause it to fail.
- The upgrade process will take about ten to fifteen minutes. As it proceeds you will see
messages and the progress bar in the middle of the loader window move through four separate steps.
No action is required during the upgrade:
- You will see a "connecting" message as the computer and receiver establish a
communications link.
- During the first step of the actual upgrade, the loader will erase the existing firmware.
- The next step will load the new firmware into the Model 1070’s memory. You will see a
"programming" progress bar while this is taking place.
- The final step will verify the upgrade.
- The Loader window will notify you when the upgrade is complete. At that point it is safe to
disconnect the serial cable and close the Loader program window.
- Please perform the "Front Panel" reset procedure as outlined in your Model 1070 Owner's Manual.
Congratulations! You have now successfully completed the software upgrade for your Model 1070
receiver. Be sure to re-enter your configuration settings, and then you are ready to enjoy the finest
in home theater!
Troubleshooting Hints:
If the computer is unable to establish communications with the Model 1070 your computer will
display an error message. Click the button in the error message window to return to the Loader,
and check the following:
- Is the serial connector at each end firmly connected? Make sure both ends are secured using
the screws on the connector head.
- Did you remember to reset the Model 1070 using the access hole on the rear panel?
- Is your Model 1070 plugged in?
- Is the Master Power switch on the rear panel turned on?
- Is the Model 1070 in the Standby mode with the amber LED the only indicator lit on the front
panel? The upgrade will not work if the Model 1070 is "on".
- Do you have the correct COM Port entered in the loader?
- Do you have the correct file name entered in the loader?
If you have tried all of these steps and are still receiving and error message, contact
Outlaw Customer Service at 866-OUTLAWS or support
|
